路由器和交换机的破解【图】

原标题：\”路由器和交换机的破解【图】\”关于路由器的知识分享。 – 素材来源网络 编辑:kaka。1首先要根据实验场景登录路由器进入全局模式去配置enable password 然后保存 # enable password 1232 破解过程（一） 开机后按“ctrl +Break”键，进入Rom 监控模式：System Bootstrap, Version 5.2(5), RELEASE SOFTWARECopyright (c) 1986-1994 byciscoSystems2500 processor with 16384 Kbytes of main memoryAbort at 0x1050450 (PC) > o/r 0x2142 (忽略Nvram 的引导配置信息 25系列) >i (重启)（二）重新启动后，进入配置模式System Bootstrap, Version 5.2(5), RELEASE SOFTWARECopyright (c) 1986-1994 by cisco Systems2500 processor with 16384 Kbytes of main memoryERR: Invalid chip id 0x80B5 (reversed = 0x1AD ) detected in System flashF3: 15020608+968908+947160 at 0x3000060 Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software – RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706Cisco Internetwork Operating System SoftwareIOS ™ 2500 Software (C2500-JS-L), Version 12.2(29), RELEASE SOFTWARE (fc3)Technical Support:http://www.cisco.com/techsupportCopyright (c) 1986-2005 by cisco Systems, Inc.Compiled Wed 11-May-05 13:19 by kellmillImage text-base: 0x0307D3C0, data-base: 0x00001000cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of memory.Processor board ID 02427741, with hardware revision 00000000Bridging software.X.25 software, Version 3.0.0.SuperLAT software (copyright 1990 by Meridian Technology Corp).TN3270 Emulation software.1 Ethernet/IEEE 802.3 interface(s)2 Serial network interface(s)32K bytes of non-volatile configuration memory.16384K bytes of processor board System flash (Read ONLY) — System Configuration Dialog —Would you like to enter the initial configuration dialog? [yes/no]: nenableconfig mem (拷贝Nvram中配置信息到memory中)Conf t(config)# enable secret cisco (修改口令)(config)# config-register 0x2102 (应用Nvram 的引导配置信息)ExitCopy run start （保存配置文件和新口令）Reload (重启，配置生效)2 下面是2600系列的 破解过程（一） 开机后按“ctrl +Break”键，进入Rom 监控模式：confreg 0x2142 （26系列）reset 重启（二）重新启动后，进入配置模式enableconfig mem (拷贝Nvram中配置信息到memory中)Conf t(config)# enable secret cisco (修改口令)(config)# config-register 0x2102 (应用Nvram 的引导配置信息)ExitCopy run start （保存配置文件和新口令）Reload (重启，配置生效)